MEPCO Bill Calculator 2026-27 (Multan + Southern Punjab Slab + TOU)
MEPCO bill calculator with 2026-27 NEPRA slab math for Multan and southern Punjab, protected vs non-protected toggle, TOU peak-hour mode, slab-crossing warning.
About the MEPCO Bill Calculator 2026-27 (Multan + Southern Punjab Slab + TOU)
Free MEPCO bill calculator for Multan Electric Power Company residential consumers, built on S.R.O. 279(I)/2026, the applicable variable charges effective February 2026. MEPCO is Pakistan's largest DISCO by service area, covering Multan, Bahawalpur, DG Khan, Vehari, Khanewal, Sahiwal, Bahawalnagar, Muzaffargarh, Layyah and Rajanpur, spanning most of southern Punjab and adjoining agricultural zones. The national rules, the slab benefit rule, Section 235 and worked examples are set out once on the all-DISCO Electricity Bill Calculator Pakistan, so this page stays on what is specific to this utility., and TOU (Time of Use, voluntary opt-in with dual meter, cheaper off-peak rate Rs 34.53 versus peak Rs 46.85 during 5 PM to 11 PM). MEPCO TOU is particularly relevant for agri tubewell consumers who can shift motor operation to off-peak hours for material savings. Killer feature is a live slab-crossing warning that fires when your current month usage is within 10 units of the next slab boundary. The national rules, the slab benefit rule, Section 235 and worked examples are set out once on the all-DISCO Electricity Bill Calculator Pakistan, so this page stays on what is specific to this utility. Built for southern Punjab households, tubewell operators and small businesses. All calculations run client-side in your browser.
Standard rate for households whose 6-month average exceeds 200 units. Progressive slabs with fixed monthly charges.
Read the current month's units from your MEPCO bill (usually labelled "Units Consumed" or "kWh").
Section 235 WHT applies to non-filers on bills over Rs 25,000
Fuel Price Adjustment. NEPRA notifies monthly. Check your last bill.
Quarterly Tariff Adjustment. Set once per quarter by NEPRA.
| Slab | Units | Rate | Charge |
|---|---|---|---|
| 301 to 400 units, applied to all 350 units | 350 | Rs 36.46 | Rs 12,761 |
| Base energy subtotal | Rs 12,761 | ||
Stay under 200 units. Six-month average below 200 unlocks protected status and Rs 14.70 per unit savings on the 51 to 100 slab plus no fixed charge.
Shift heavy loads off-peak. Rs 12.32 per unit gap between peak and off-peak TOU rates. Agri tubewell consumers on TOU save the most by running motors through the night.
File your FBR return. Non-filers pay 7.5% extra as Section 235 WHT on bills over Rs 25,000. On a Rs 30,000 bill that is Rs 2,250 saved per month by filing.
Base tariff slabs verified against S.R.O. 279(I)/2026 applicable variable charges effective February 2026, as published by the DISCOs themselves. MEPCO serves Multan, Bahawalpur, DG Khan, Vehari, Khanewal, Sahiwal and most of southern Punjab on the uniform NEPRA A-1 domestic tariff. NEPRA notifies FPA every month and QTR every quarter.
Get pinpoint accuracy: read the exact FPA and QTR values from your current MEPCO bill and enter them above. That gives a number within Rs 100 of the actual bill in almost all cases. Verify at the NEPRA MEPCO tariff page. This is an estimate tool. Actual bills may vary due to arrears, adjustments, meter reading errors and cycle-specific NEPRA notifications.
How to use the MEPCO Bill Calculator 2026-27 (Multan + Southern Punjab Slab + TOU)
- Pick your consumer type: Protected if your six-month average consumption is 200 units or less, Non-protected if higher, or TOU if you have opted into the Time of Use dual-meter tariff via your MEPCO SDO.
- Enter the units consumed this month, read directly from the MEPCO bill (usually labelled Units Consumed or kWh). For TOU, enter peak and off-peak units separately.
- Set filer status. Non-filers pay a 7.5 percent Section 235 withholding tax on bills over Rs 25,000; filers do not. Filing your FBR return saves this amount every month.
- Adjust FPA and QTR to match the exact per-unit values on your current bill. Defaults are conservative mid-cycle values but NEPRA updates FPA monthly and QTR quarterly.
- Read the result. The primary card shows the total payable and effective per-unit rate. Slab-by-slab breakdown table shows exactly which rate applied to which portion of your consumption. Watch for the red slab-crossing warning if your usage is close to the next slab boundary.
- Verify against your MEPCO bill. Actual bills may vary due to arrears, adjustments, meter reading errors and cycle-specific NEPRA notifications. Confirm the exact number on your official bill or the NEPRA MEPCO tariff page before disputing any charges.
Frequently Asked Questions
Sources
Rates, slabs and formulas used in this calculator are cross-checked against the following official sources. Always verify the latest number on the original page before making a financial decision.
Related Tools
Discover more free tools
Toolsfluent has dozens of fast, privacy-friendly tools that work right in your browser. Explore by category to find what you need.
Browse all tools →